All purpose drywall compound or Lightweight all purpose drywall compound can be used to coat corner bead. Mud used to coat corner bead is some of the thicker mud you will use. Only a small amount of water is added to thin it slightly. However, if it is too thick, it will be hard to apply so go ahead and thin it slightly but it should be thicker than most coating mud. Thicker mud makes it easier to fil the gap created between the bead and the drywall.
Slightly thinner mud can be used for second coating corner bead. Thinner mud makes it easier to smooth out the imperfections that were left behind from the first coat. Using an eight or ten inch drywall knife, spread drywall compound evenly on the drywall near the corner bead. The knife should run against the bead as a guide.
The mud should be evenly dispersed across and under the knife. Notice how the two fingers are pressed against the mid section of the drywall knife.
This helps to ensure even pressure and control when applying mud. Start applying mud from the top down. You probably don't want to start at the very top of the bead but somewhere above center. The idea is that as you add more mud, you will want to add it above, pulling it into the previously applied mud.
Most tapers place the metal corner bead first. This is primarily because if you were to do any taping first you'd have to wait until that dries to install corner bead. It's a matter of efficiency. It's also usually best to keep metal bead set snugly to the drywall, with nothing behind it. This allows you to keep it straighter and on plane. It should protrude just slightly on both walls when a straightedge is set against the drywall perpendicular to the bead.
There's tape all over the building that's not tucked under anything and it's not an issue. All that said, drywall taping is something of an art and you're free to do what makes sense for you and your project. Just remember the cardinal rule: lighter is better. The pros I've worked with do very little sanding to produce fantastic results, and it's far easier and less messy to skim on another coat than to grind down humps.
The corner bead that I use is pre taped. Put mud on the wall and push the bead in and work the mud out and over the tape. If using the bare metal anchor with screws then mud and tape. Putting tape under the corner bead will make it bulkier and not have a nice crisp corner. Mechanically attach metal corner bead to the drywall or framing with staples or nails. Next put sticky mesh tape over the metal to drywall transition on each side, then fill will all purpose joint compound, let dry, then put lightweight joint compound over that.
Sign up to join this community. The best answers are voted up and rise to the top. Stack Overflow for Teams — Collaborate and share knowledge with a private group.
Create a free Team What is Teams? Learn more. Tape vs corner bead order of installation Ask Question. And since it doesn't require an underlying layer of compound, mesh allows for a thinner buildup over butt joints and repairs.
You can use mesh anywhere except inside corners. For a durable finish use setting-type joint compound, also called mud , for the first coat over the metal. Ready-mixed can be used for the second and finish coats, but it's too soft and prone to shrinking when used in a thick application like that required to cover metal corner bead. Plan on using one full corner bead for each corner , using either 8-foot or foot bead. If there are soffits or other structures with outside corners , measure the total length of all of these elements and divide by the length of a single corner bead 8 or Install drywall corner bead Costs.
Your actual price will depend on job size, conditions, finish options you choose. Any vertical molding used to protect the external angle of the intersecting surfaces. A strip of formed galvanized iron, sometimes combined with a strip of metal lath, placed on corners to reinforce them before plastering. All purpose drywall compound or Lightweight all purpose drywall compound can be used to coat corner bead. Mud used to coat corner bead is some of the thicker mud you will use.
Only a small amount of water is added to thin it slightly. Use a 6-inch joint knife to fill any gaps between the two walls with drywall compound. The fiberglass mesh tape is more likely to allow cracks to form over time because it is not as strong as paper tape. Fiber glass mesh is designed to be used with fast setting mud.
This is dry stuff that is mixed with water and contains plaster of paris. Metal Tape It is relatively inexpensive compared to newer products, and easier to install. Just cover the outside angle with joint compound, place a length of metal tape over it, and pinch the metal tape into place.
Apply a few heavy coats of joint compound, and the wide angle is finished. Are you supposed to tape corner bead? Category: hobbies and interests beadwork. Put mud on the wall and push the bead in and work the mud out and over the tape. Putting tape under the corner bead will make it bulkier and not have a nice crisp corner. Which corner bead is best? Does drywall tape need to be completely covered?
What size taping knives do I need?
0コメント